Download Beat-aligning Guitar Looper
Loopers become more and more popular due to their growing features and capabilities, not only in live performances but also as a rehearsal tool. These effect units record a phrase and play it back in a loop. The start and stop positions of the recording are typically the player’s start and stop taps on a foot switch. However, if these cues are not entered precisely in time, an annoying, audible gap may occur between the repetitions of the phrase. We propose an algorithm that analyzes the recorded phrase and aligns start and stop positions in order to remove audible gaps. Efficiency, accuracy and robustness are achieved by including the phase information of the onset detection function’s STFT within the beat estimation process. Moreover, the proposed algorithm satisfies the response time required for the live application of beat alignment. We show that robustness is achieved for phrases of sparse rhythmic content for which there is still sufficient information to derive underlying beats.
Download Estimating Pickup and Plucking Positions of Guitar Tones and Chords with Audio Effects
In this paper, we introduce an approach to estimate the pickup position and plucking point on an electric guitar for both single notes and chords recorded through an effects chain. We evaluate the accuracy of the method on direct input signals along with 7 different combinations of guitar amplifier, effects, loudspeaker cabinet and microphone. The autocorrelation of the spectral peaks of the electric guitar signal is calculated and the two minima that correspond to the locations of the pickup and plucking event are detected. In order to model the frequency response of the effects chain, we flatten the spectrum using polynomial regression. The errors decrease after applying the spectral flattening method. The median absolute error for each preset ranges from 2.10 mm to 7.26 mm for pickup position and 2.91 mm to 21.72 mm for plucking position estimates. For strummed chords, faster strums are more difficult to estimate but still yield accurate results, where the median absolute errors for pickup position estimates are less than 10 mm.
Download Block-oriented Gray Box Modeling of Guitar Amplifiers
In this work, analog guitar amplifiers are modeled with an automated procedure using iterative optimization techniques. The digital model is divided into functional blocks, consisting of lineartime-invariant (LTI) filters and nonlinear blocks with nonlinear mapping functions and memory. The model is adapted in several steps. First the filters are measured and afterwards the parameters of the digital model are adapted for different input signals to minimize the error between itself and the analog reference system. This is done for a small number of analog reference devices. Afterwards the adapted model is evaluated with objective scores and a listening test is performed to rate the quality of the adapted models.
Download Modeling Circuits with Operational Transconductance Amplifiers Using Wave Digital Filters
In this paper, we show how to expand the class of audio circuits that can be modeled using Wave Digital Filters (WDFs) to those involving operational transconductance amplifiers (OTAs). Two types of behavioral OTA models are presented and both are shown to be compatible with the WDF approach to circuit modeling. As a case study, an envelope filter guitar effect based around OTAs is modeled using WDFs. The modeling results are shown to be accurate when to compared to state of the art circuit simulation methods.
Download Comparison of Germanium Bipolar Junction Transistor Models for Real-time Circuit Simulation
The Ebers-Moll model has been widely used to represent Bipolar Junction Transistors (BJTs) in Virtual Analogue (VA) circuits. An investigation into the validity of this model is presented in which the Ebers-Moll model is compared to BJT models of higher complexity, introducing the Gummel-Poon model to the VA field. A comparison is performed using two complementary approaches: on fit to measurements taken directly from BJTs, and on application to physical circuit models. Targeted parameter extraction strategies are proposed for each model. There are two case studies, both famous vintage guitar effects featuring germanium BJTs. Results demonstrate the effects of incorporating additional complexity into the component model, weighing the trade-off between differences in the output and computational cost.
Download A Continuous Frequency Domain Description of Adjustable Boundary Conditions for Multidimensional Transfer Function Models
Physical modeling of string vibrations strongly depends on the conditions at the system boundaries. The more complex the boundary conditions are the more complex is the process of physical modeling. Based on prior works, this contribution derives a general concept for the incorporation of complex boundary conditions into a transfer function model designed with simple boundary conditions. The concept is related to control theory and separates the treatment of the boundary conditions from the design of the string model.
Download Harmonic-percussive Sound Separation Using Rhythmic Information from Non-negative Matrix Factorization in Single-channel Music Recordings
This paper proposes a novel method for separating harmonic and percussive sounds in single-channel music recordings. Standard non-negative matrix factorization (NMF) is used to obtain the activations of the most representative patterns active in the mixture. The basic idea is to classify automatically those activations that exhibit rhythmic and non-rhythmic patterns. We assume that percussive sounds are modeled by those activations that exhibit a rhythmic pattern. However, harmonic and vocal sounds are modeled by those activations that exhibit a less rhythmic pattern. The classification of the harmonic or percussive NMF activations is performed using a recursive process based on successive correlations applied to the activations. Specifically, promising results are obtained when a sound is classified as percussive through the identification of a set of peaks in the output of the fourth correlation. The reason is because harmonic sounds tend to be represented by one valley in a half-cycle waveform at the output of the fourth correlation. Evaluation shows that the proposed method provides competitive results compared to other reference state-of-the-art methods. Some audio examples are available to illustrate the separation performance of the proposed method.
Download Kinematics of Ideal String Vibration Against a Rigid Obstacle
This paper presents a kinematic time-stepping modeling approach of the ideal string vibration against a rigid obstacle. The problem is solved in a single vibration polarisation setting, where the string’s displacement is unilaterally constrained. The proposed numerically accurate approach is based on the d’Alembert formula. It is shown that in the presence of the obstacle the lossless string vibrates in two distinct vibration regimes. In the beginning of the nonlinear kinematic interaction between the vibrating string and the obstacle the string motion is aperiodic with constantly evolving spectrum. The duration of the aperiodic regime depends on the obstacle proximity, position, and geometry. During the aperiodic regime the fractional subharmonics related to the obstacle position may be generated. After relatively short-lasting aperiodic vibration the string vibration settles in the periodic regime. The main general effect of the obstacle on the string vibration manifests in the widening of the vibration spectra caused by transfer of fundamental mode energy to upper modes. The results presented in this paper can expand our understanding of timbre evolution of numerous stringed instruments, such as, the guitar, bray harp, tambura, veena, sitar, etc. The possible applications include, e.g., real-time sound synthesis of these instruments.
Download Real-time Physical Model of a Wurlitzer and Rhodes Electronic Piano
Two well known examples of electro-acoustical keyboards played since the 60s to the present day are the Wurlitzer electric piano and the Rhodes piano. They are used in such diverse musical genres as Jazz, Funk, Fusion or Pop as well as in modern Electronic and Dance music. Due to the popularity of their unique sound and timbre, there exist various hardware and software emulations which are either based on a physical model or consist of a sample based method for sound generation. In this paper, a real-time physical model implementation of both instruments using field programmable gate array (FPGA) hardware is presented. The work presented herein is an extension of simplified models published before. Both implementations consist of a physical model of the main acoustic sound production parts as well as a model for the electromagnetic pickup system. Both models are compared to a series of measurements and show good accordance with their analog counterparts.
Download Automatic Decomposition of Non-linear Equation Systems in Audio Effect Circuit Simulation
In the digital simulation of non-linear audio effect circuits, the arising non-linear equation system generally poses the main challenge for a computationally cheap implementation. As the computational complexity grows super-linearly with the number of equations, it is beneficial to decompose the equation system into several smaller systems, if possible. In this paper we therefore develop an approach to determine such a decomposition automatically. We limit ourselves to cases where an exact decomposition is possible, however, and do not consider approximate decompositions.